Skip to content
Rezo

PoE injectors

Which injector suits your device? Contact us for advice or a quote

Filter by

Brand

Price incl. VAT

Price incl. VAT

Ethernet interface type

Ethernet interface type

Ethernet LAN (RJ-45) ports

Ethernet LAN (RJ-45) ports

PoE injectors to power Wi-Fi access points, IP cameras and phones

A PoE injector sends power down the Ethernet cable, so a Wi-Fi access point, IP camera or phone can run far from any mains socket. The range covers single-port PoE, PoE+ and PoE++ injectors, multi-port midspan units and PoE splitters, which do the reverse job. There are also PoE+ switches for powering several devices from the rack, as well as Ubiquiti's UniFi adapters.

The typical case is a ceiling-mounted access point connected by a single cable to a router or a switch without PoE. A camera on an outside wall or a Wi-Fi unit on a mast works the same way, with the injector kept safely in the comms room. A splitter does the reverse at the far end of the cable. It takes the power off the line for a device without PoE, and StarTech.com's industrial models offer a 12 to 48 V DC output.

Power sets the first cut. A 7 or 12 W injector is enough for a small access point, and 30 W PoE+ suits many wireless units and cameras. PoE++ at 60 W, or 90 W over 4 pairs under the 802.3bt standard, is for motorised cameras and power-hungry equipment. Speed matters just as much. A Fast Ethernet injector caps the whole link, whereas Gigabit, 2.5 Gbit/s, 5 Gbit/s and 10 GbE models carry the full throughput of a recent access point.

Passive PoE causes the most unpleasant surprises. Unlike an 802.3at or 802.3bt injector, a passive one, such as TP-Link's Omada model, supplies a fixed voltage without checking what is connected. On equipment that does not expect it, it may fail to start the device or even damage it. Check the voltage, standard and power the device requires, and plan for a mains socket near the injector and a cable category that matches the target speed.

For a home or a single desk, a single-port injector powers one access point or camera without replacing the switch. Once access points in several offices or classrooms need power, a 4-port midspan injector, a Planet Technology Corp. PoE hub or a Netgear, Cisco or Zyxel PoE+ switch brings power together in the rack. The total power budget then has to cover the combined draw of every device, not just the number of ports.

Ubiquiti covers both passive PoE at 24, 48 or 50 V and multi-gigabit UniFi adapters, which makes it easy to stick to one range across a fleet of access points. StarTech.com offers DIN-rail industrial units, a wall-mounted 4-port midspan and a 5 Gbit/s injector with a 160 W budget. D-Link, Trendnet, Level One, Digitus, Extralink and HP add Gigabit injectors for powering one or 2 devices.

To help you choose, read our guide Small business network and Wi-Fi.

Frequently asked questions

What is the difference between a passive PoE injector and an 802.3at or 802.3bt one?

A standards-based 802.3at or 802.3bt injector first checks that the device accepts PoE, then supplies the power it requests. A passive injector sends a fixed voltage all the time, without that handshake.

So it only suits devices built to take that exact voltage, which their documentation will confirm.

How much power do I need for a Wi-Fi access point or an IP camera?

Start from the consumption stated by the device manufacturer. A 7 to 15 W injector is enough for a small access point, while 30 W PoE+ covers many wireless units and fixed cameras.

Motorised or heated cameras and more demanding equipment need PoE++ at 60 W or 90 W, depending on the model.

Is a Fast Ethernet injector enough for a recent Wi-Fi access point?

No. A Fast Ethernet injector caps the speed of the whole link, whatever the access point can do. It is fine for a basic camera or older equipment.

For a recent Wi-Fi access point, choose at least a Gigabit model, or 2.5 Gbit/s or 10 GbE if its network port supports it.

Should I use PoE injectors or a PoE switch for several devices?

A single-port injector is a convenient way to add one or 2 devices to an existing network. Beyond that, a multi-port midspan injector or a PoE+ switch brings power together in the rack, with fewer mains adapters.

Either way, make sure the total power budget covers all the devices.

What is a PoE splitter used for?

A splitter sits at the far end of the cable. It separates data and power to supply a device without PoE support, such as a small camera or a network box.

Its output voltage must match the device. StarTech.com's industrial models offer a 12 to 48 V DC output.

Will a UniFi injector work with a device from another brand?

Yes, as long as the standard and voltage match. UniFi PoE+ adapters that comply with 802.3at can power any device that supports that standard.

Ubiquiti's passive 24 or 50 V injectors, however, only suit equipment that expects that voltage, so check this for each model.

Where should a PoE injector go in a cabinet or comms room?

The injector sits near the mains socket and the switch, usually in the comms room, while the powered device can be some distance away. Desktop models go on a shelf, StarTech.com's 4-port midspan mounts on a wall and the industrial units fit on a DIN rail in an electrical cabinet.